HN-Sound /PA-Chassis/2 Zoll TreiberArtikel

18 Sound HD2080T 235,00 EUR

SMALL SPECIFICATIONS

109 dB SPL 1W / 1m average sensitivity

2 inch exit throat

3 inch voice coil diameter

160W continuous program power handling

Polyethilene - Titanium diaphragm assembly

Copper shorting ring on pole pieces

GENERAL SPECIFICATIONS
Throat Diameter	50 mm (2 in)
Rated Impedance	8 ohm
DC Resistance	6,2 Ohm
Minimum Impedance	8 Ohm at 3500Hz
Power handling	(1200 � 20000 Hz)
Continuous Pink Noise (1)	80W above 1,2 kHz
Continuous Program (2)	160W above 1,2 kHz
Sensitivity(1W@1m) (3)	109 dB
Frequency Range	500Hz � 20kHz
Recomm. Xover Frequency	above 800Hz (12dB/oct slope)
Diaphragm Material	Titanium - polyethilene
Voice Coil Diameter	74,4mm (2 93 in)
Voice Coil Winding Material	Edge-wound aluminum
Magnet Material	Ferrite
Flux Density	1,8 T
BL Factor	12,8 N/A
Polarity	Positive voltage on + terminal gives positive pressure in the throat

MOUNTING INFORMATIONS
Overall diameter	169 mm (6,65 in)
Mounting holes diameter	4 M6 holes 90� at � 102 mm (4 in)
Bolt circle diameter	102 mm (4 in)
Total depth	75,4 mm (3 in)
Net weight	5,3 Kg (11,60 lb)
Shipping weight	5,5 Kg (12,10 lb)
CardBoard Packaging dimensions	170x170x80 mm (6,7x6,7x3,2 in)

The HD2080T has been designed for use in high quality audio systems. With a direct 2-inch exit throat, the HD2080T has been developed to match the XR2064 constant directivity horn.
The motor structure, throughout the precisely coherent phase plug with 3 circumferential slots and copper ring on the pole piece, reduces inductance effects and distortion. Four top plate air ducts have been designed to act as a loading chamber for the diaphragm, implementing mid band distortion and response figures.
The HD2080T diaphragm assembly is composed of a titanium dome sandwiched to a proprietary treated polyester suspension unit. It has been designed to maintain low resonance, lowering the minimum crossover point value at 1,2kHz.
Thanks to its physical properties, the proprietary treated Nomex former has a 30% higher value of tensile elongation at a working operative temperature (200�C) when compared to Kapton. This feature enables proper energy transfer control from the voice coil to the dome in real working conditions. Moreover, this proprietary former material is also suitable to for use in higher moisture content environments.
The HD2080T powerful ceramic magnet assembly has been designed to obtain 16KGauss in the gap.
Excellent heat dissipation and thermal exchange are guaranteed by the direct contact between the magnetic structure and the aluminum cover which leads to a lower power compression value.

18 Sound ND2060A 329,00 EUR

SMALL SPECIFICATIONS

110 dB 1W/1m average sensitivity

2 inch exit throat

3 inch voice coil diameter

150 W continuous program power handling

Pure Aluminum dome

Neodymium magnetic structure

Excellent thermal exchange

GENERAL SPECIFICATIONS
Throat Diameter	50 mm (2 in)
Rated Impedance	8 ohm
DC Resistance	6,2 ohm
Minimum Impedance	8 ohm at 3500 Hz
Le (at 1kHz)	124 �H
Power handling	(800 � 20000 Hz)
Continuous Pink Noise (1)	75 W above 1,2 kHz
Continuous Program (2)	150 W above 1,2 kHz
Sensitivity(1W@1m) (3)	110 dB
Frequency Range	500 Hz � 20 kHz
Recomm. Xover Frequency	Above 800Hz (12 dB/oct slope)
Diaphragm Material	Pen - Aluminum
Voice Coil Diameter	74,4 mm (2,93 in)
Voice Coil Winding Material	Edge-wound aluminum
Magnet Material	Neodymium
Flux Density	1,9 T
BL Factor	13,5 N/A
Polarity	Positive voltage on red terminal gives positive pressure in the throat

MOUNTING INFORMATIONS
Overall diameter	132,5 mm (5,22 in)
Mounting holes diameter	4 M6 holes 90� at �102 mm (4 in)
Bolt circle diameter	102mm (4 in)
Total depth	99 mm (3,9 in)
Net weight	3,6 kg (7,9 lb)
Shipping weight	4 kg (8,8 lb)
CardBoard Packaging dimensions	132x132x103 mm(5,2x5,2x4,1 in)

The ND2060A 2 inch exit neodymium HF compression driver has been designed for high quality sound systems application.
The ND2060A diaphragm assembly is composed by an aluminum dome sandwiched to a proprietary treated polyester suspension. This design maintains low resonance and lowers the minimum crossover point value at 800 Hz. The composite diaphragm assembly is made by an aluminum dome strongly joined to the PEN suspension, in order to assure unmatched transient response. The lower density of the aluminum and PEN structure permits higher levels of sensitivity, especially in the mid-high frequency range. The unique ellipsoidal suspension shape has been designed to maintain 3rd harmonic distortion value lower than 0.05% over all working frequency range.
A bended former edge-wound aluminum 75mm voice coil completes the diaphragm assembly. The proprietary treated Nomex former material shows 30% higher value of tensile elongation at working operative temperature (200�C) when compared to Kapton. Moreover, Nomex is suitable to work also in higher moisture contents environments. The bended former is joint in a sandwich configuration between PEN suspension and the aluminum dome, assuring extended frequency energy transfer for improved response linearity and unparallel reliability.
Through careful use of elementary pieces of neodymium magnets, Eighteen Sound engineers have developed a powerful neodymium magnet assembly able to reach 19 KGauss in the gap in a compact and lightweight structure. The motor structure, throughout the precisely coherent phase plug with 3 circumferential slots and copper ring on the pole piece, reduces inductance effects and distortion. Four top plate air ducts were designed to act as a loading chamber for the diaphragm, implementing mid band distortion and response figures.
The custom designed O-ring creates a tight seal between the plate and the cover assuring air chamber loading. Excellent heat dissipation and thermal exchange are guaranteed by the direct contact between the magnetic structure and the aluminum cover that allows to obtain a lower power compression value.
For the increase in use of high power audio systems at outdoor events or in marine environments, the ability to perform properly under inclement weather conditions is a key-point. The special coating applied to the magnet and the top and back plates of the magnetic structure makes the ND2060A compression driver resistant to the corrosive effects of salts and oxidization.

18 Sound ND2060 335,00 EUR

SMALL SPECIFICATIONS

109 dB SPL 1W / 1m average sensitivity

2 inch exit throat

3 inch voice coil diameter

200 W continuous program power handling

Pure Titanium diaphragm assembly

Excellent thermal exchange

Neodymium magnetic structure

GENERAL SPECIFICATIONS
Throat Diameter	50 mm (2 in)
Rated Impedance	8 ohm
DC Resistance	6,2 ohm
Minimum Impedance	8 ohm at 3500 Hz
Le (at 1kHz)	124 �H
Power handling	(800 � 20000 Hz)
Continuous Pink Noise (1)	100 W above 1,2 kHz
Continuous Program (2)	200 W above 1,2 kHz
Sensitivity(1W@1m) (3)	109 dB
Frequency Range	500 Hz � 20 kHz
Recomm. Xover Frequency	800Hz (12 dB/oct slope)
Diaphragm Material	Titanium
Voice Coil Diameter	74,4 mm (2,93 in)
Voice Coil Winding Material	Edge-wound aluminum
Magnet Material	Neodymium
Flux Density	1,9 T
BL Factor	13,5 N/A
Polarity	Positive voltage on red terminal gives positive pressure in the throat

MOUNTING INFORMATIONS
Overall diameter	132,5 mm (5,22 in)
Mounting holes diameter	4 M6 holes 90� at �102 mm (4 in)
Bolt circle diameter	102mm (4 in)
Total depth	99 mm (3,9 in)
Net weight	3,6 kg (7,9 lb)
Shipping weight	4 kg (8,8 lb)
CardBoard Packaging dimensions	132x132x103 mm(5,2x5,2x4,1 in)

The ND2060 high frequency compression driver has been designed for high level sound systems application. With a 2-inch exit throat, the ND2060 has been developed to work with any standard 2-inch horn.
Its titanium diaphragm is produced in house and has been developed to assure unmatched transient response. The diaphragm assembly is made by joining the former directly to the titanium dome on its upper bend edge. In comparison with a usual straight former joint, the driver�s design assures extended frequency energy transfer for improved response linearity and unparallel reliability. This feature facilitates proper motion control of the dome in real working conditions. A proprietary treated Nomex former is used as shows a 30% higher value of tensile elongation at a working operative temperature (200�C) when compared to Kapton. Moreover, this proprietary former material is also suitable for use in higher moisture content environments.
The big innovation in ND2060 consists of its new innovative magnetic architecture. By careful use of elementary pieces of neodymium magnets, Eighteen Sound engineers have developed a powerful neodymium magnet assembly able to reach 19KGauss in the gap in compact and lightweight structures. The motor structure, throughout the precisely coherent phase plug with 3 circumferential slots and copper ring on the pole piece, reduces inductance effects and distortion. Four top plate air ducts have been designed to act as a loading chamber for the diaphragm, implementing mid band distortion and response figures.
The custom designed O-ring creates a tight seal between the plate and the cover assuring air chamber loading. Excellent heat dissipation and thermal exchange are guaranteed by the direct contact between the magnetic structure and the aluminum cover which leads to a lower power compression value.
Due to the increasing use of high power audio systems at outdoor events or in marine environments, the ability of equipment to perform properly under inclement weather conditions is a key feature of Eighteen Sound philosophy. Hence, a special treatment has been applied to the magnet and the top and back plates of the magnetic structure which make the driver more resistant to the corrosive effects of salts and oxidization. This treatment is more effective than any other treatment in use by other manufacturers.

18 Sound ND2080 495,00 EUR

SMALL SPECIFICATIONS

110 dB SPL 1W / 1m average sensitivity

2 inch exit throat

3 inch voice coil diameter

200 W continuous program power handling

Pure Titanium diaphragm assembly

Excellent thermal exchange

Neodymium ring magnetic structure

GENERAL SPECIFICATIONS
Throat Diameter	50 mm (2 in)
Rated Impedance	8 ohm
DC Resistance	6,2 ohm
Minimum Impedance	8 ohm at 3500 Hz
Le (at 1kHz)	124 �H
Power handling
Continuous Pink Noise (1)	100 W above 1,2 kHz
Continuous Program (2)	200 W above 1,2 kHz
Sensitivity(1W/1m) (3)	110 dB
Frequency Range	500 Hz � 20 kHz
Recomm. Xover Frequency	800Hz 12 dB/octave
Diaphragm Material	Titanium
Voice Coil Diameter	74,4 mm (2,93 in)
Voice Coil Winding Material	Edge-wound aluminum
Magnet Material	Neodymium
Flux Density	2,2 T
BL Factor	15,5 N/A
Polarity	Positive voltage on red terminal gives positive pressure in the throat

MOUNTING INFORMATIONS
Overall diameter	131 mm (5,1 in)
Mounting holes diameter	4 M6 holes 90� at �102 mm (4 in)
Bolt circle diameter	102mm (4 in)
Total depth	99 mm (3,9 in)
Net weight	3,6 kg (7,9 lb)
Shipping weight	4 kg (8,8 lb)
CardBoard Packaging dimensions	132x132x103 mm(5,2x5,2x4,1 in)

The ND2080 high frequency compression driver has been designed for high level sound systems application. With a 2-inch exit throat, the ND2080 has been developed to work with any standard 2-inch horn.
The titanium diaphragm is produced in house and has been developed to assure unmatched transient response. The diaphragm assembly is made by joining the former directly to the titanium dome on its upper bend edge. In comparison with a usual straight former joint, the driver design assures extended frequency energy transfer for improved response linearity and unparallel reliability. This feature allows proper motion control of the dome in real working conditions. A proprietary treated Nomex former is used as Nomex shows a 30% higher value of tensile elongation at a working operative temperature (200�C) when compared to Kapton. Moreover, this proprietary former material is also suitable for use in higher moisture content environments.
The ND2080 powerful neodymium magnet assembly has been designed to obtain 22KGauss in the gap for major benefits in transient response. The motor structure, throughout the precisely coherent phase plug with 3 circumferential slots and copper ring on the pole piece, reduces inductance effect and distortion. Four top plate air ducts have been designed to act as a loading chamber for the diaphragm, implementing mid band distortion and response figures.
The custom designed O-ring creates a tight seal between the plate and the cover assuring air chamber loading. Excellent heat dissipation and thermal exchange are guaranteed by the direct contact between the magnetic structure and the aluminum cover which leads to a lower power compression value.
Due to the increasing use of high power audio systems at outdoor events or in marine environments, the ability of equipment to perform properly under inclement weather conditions is a key feature of Eighteen Sound philosophy. Hence, a special treatment is applied to the magnet and the top and back plates of the magnetic structure making the driver more resistant to the corrosive effects of salts and oxidization. This treatment is more effective than any other treatment used by other manufacturers.

B&C DCM 50 Driver 495,00 EUR

160 W continuous program power capacity

2� horn throat diameter

400 � 10000 Hz response

108.5 dB sensitivity

Neodymium magnet assembly

Specifications

Throat Diameter 50 mm (2 in)

Nominal Impedance 8 ohm

Minimum Impedance 8 ohm

Nominal Power Handling 80 W

Continuous Power Handling 160 W

Sensitivity (1W/1m) 108.5 dB

Frequency Range 0.4 - 10 kHz

Recommended Crossover 400 kHz

Voice Coil Diameter 51 mm (2.00 in)

Winding Material Aluminium

Inductance 0.18 mH

Diaphragm material Composite

Flux Density 2.1 T

Mounting and Shipping info

Overall Diameter 152 mm (6 in)

Depth 108 mm (4.25 in)

Net Weight 3.2 kg (7 lb)

Shipping Weight 3.4 kg (7.5 lb)

Shipping Box 170x170x140 mm (6.7x6.7x5.5 in)

B&C DE 1000 Driver 535,00 EUR

280 W continuous program power capacity

1.5� horn throat diameter

100 mm (4 in) aluminium voice coil

Titanium diaphragm

500 � 20000 Hz response

109 dB sensitivity

Neodymium magnet assembly with shorting copper cap

Specifications

Throat Diameter 38 mm (1.5 in)

Nominal Impedance 8 ohm

Minimum Impedance 8.1 ohm

Nominal Power Handling 140 W

Continuous Power Handling 280 W

Sensitivity (1W/1m) 109 dB

Frequency Range 1 - 20 kHz

Recommended Crossover 1 kHz

Voice Coil Diameter 100 mm (4.00 in)

Winding Material Aluminium

Inductance 0.18 mH

Diaphragm material Titanium

Flux Density 1.95 T

Mounting and Shipping info

Overall Diameter 154 mm (6.1 in)

Depth 60 mm (2.4 in)

Net Weight 3.4 kg (7.5 lb)

Shipping Weight 3.7 kg (8.1 lb)

Shipping Box 195x195x100 mm (7.7x7.7x3.9 in)

B&C DE 950TN Driver 585,00 EUR

220 W continuous program power capacity

2� horn throat diameter

75 mm (3 in) aluminium voice coil

Titanium diaphragm

500 � 18000 Hz response

108.5 dB sensitivity

Neodymium magnet assembly with shorting copper cap

Specifications

Throat Diameter 50 mm (2 in)

Nominal Impedance 8 ohm

Minimum Impedance 8.3 ohm

Nominal Power Handling 110 W

Continuous Power Handling 220 W

Sensitivity (1W/1m) 108.5 dB

Frequency Range 0.5 - 18 kHz

Recommended Crossover 0.8 kHz

Voice Coil Diameter 75 mm (3.00 in)

Winding Material Aluminium

Inductance 0.14 mH

Diaphragm material Titanium

Flux Density 2.05 T

Mounting and Shipping info

Overall Diameter 131 mm (5.2 in)

Depth 85 mm (3.3 in)

Net Weight 2.7 kg (5.9 lb)

Shipping Weight 11.4 kg (25.1 lb)

Shipping Box 300x160x210 mm (11.8x6.3x8.3 in)

B&C DE 64TN Driver 245,00 EUR

220 W continuous program power capacity

2� horn throat diameter

75 mm (3 in) aluminium voice coil

500 � 18000 Hz response

107.5 dB sensitivity

Shorting copper cap for extended HF response

Specifications

Throat Diameter 50 mm (2 in)

Nominal Impedance 8 ohm

Minimum Impedance 8.4 ohm

Nominal Power Handling 110 W

Continuous Power Handling 220 W

Sensitivity (1W/1m) 107.5 dB

Frequency Range 0.5 - 18 kHz

Recommended Crossover 1 kHz

Voice Coil Diameter 75 mm (3.00 in)

Winding Material Aluminium

Inductance 0.14 mH

Diaphragm material Titanium

Flux Density 1.6 T

Mounting and Shipping info

Overall Diameter 156 mm (6.1 in)

Depth 66 mm (2.6 in)

Net Weight 4.1 kg (9 lb)

Shipping Weight 8.8 kg (19.3 lb)

Shipping Box 210x210x190 mm (8.3x8.3x7.5 in)

B&C DE 1050 Driver 575,00 EUR

280 W continuous program power capacity

2� horn throat diameter

100 mm (4 in) aluminium voice coil

Titanium diaphragm

500 � 20000 Hz response

109 dB sensitivity

Neodymium magnet assembly with shorting copper cap

Specifications

Throat Diameter 50 mm (2 in)

Nominal Impedance 8 ohm

Minimum Impedance 8.1 ohm

Nominal Power Handling 140 W

Continuous Power Handling 280 W

Sensitivity (1W/1m) 109 dB

Frequency Range 0.5 - 20 kHz

Recommended Crossover 0.8 kHz

Voice Coil Diameter 100 mm (4.00 in)

Winding Material Aluminium

Inductance 0.18 mH

Diaphragm material Titanium

Flux Density 1.95 T

Mounting and Shipping info

Overall Diameter 154 mm (6.1 in)

Depth 85 mm (3.3 in)

Net Weight 3.6 kg (7.9 lb)

Shipping Weight 3.9 kg (8.6 lb)

Shipping Box 195x195x100 mm (7.7x7.7x3.9 in)